Follow

OmniBridge-40

This article is for general configuration to be used for deployment of an OmniWAN OmniBridge-40 (4 port model).

 

 

Port Setup

 

PORT1 = Primary WAN

PORT4 = Primary LAN

PORT2-PORT3 = Open for either LAN or as additional WAN (If additional WAN links ordered)

Option of WAN or LAN: Secondary, Tertiary, etc WAN Active only if subscription was ordered with extra WAN links

 

Topology

OmniBridge can function behind an existing router, however it is preferable to have your OmniBridge connected directly to the upstream ISP modem.  Its important your OmniBridge has dedicated access to the upstream router to best perform its job at controlling bandwidth provided by the ISP*.   

 

Before beginning, make sure to log into the www.mdsmanager.com account that was used to order the OmniBride your are setting up, locate your OmniBridge and leave this page open.

 

WARNING:  Do not use ISP DNS servers for clients behind OmniWAN.  ISPs usually block DNS traffic coming from a network outside their own.  Once OmniWAN is deployed, your egress and ingress is at our DC, therefore it looks like the request is coming form a network outside their own

 

Initial OmniBridge Setup

 

1. Plug the OmniBridge PORT1 (WAN) into an internet enabled upstream network running a DHCP server

- The OmniBridge should show online in your portal

 

2. Go back to your www.mdsmanager.com portal and configure the Zones tab as needed

- Make sure the LAN IP you configure DOES NOT match the IP for the upstream network's gateway (LAN Network IP must be unique from the upstream gateway's)

 

3. Plug a test client into OPT2/LAN (Primary LAN Network)

- Verify your MDS protection by navigating to shieldtest.com and running a ShieldTest

 

4. IMPORTANT: Make sure to schedule a 30 Minute window with your customer to run Optimization on the OmniBridge since this testing is disruptive when run. 

a. On www.mdsmanager.com, go to the OmniWAN tab for the subscription

b. Click the "Optimize" button to have OmniWAN immediately begin tuning your ISP links

c. Make sure it completes successfully

If you need it scheduled or have issues with optimization, please send an email to support@omninet.io

 

 

 

WAN Static IP Configuration

***WARNING MAKE SURE YOU HAVE THE CORRECT STATIC IP INFO FROM THE ISP TO AVOID ACCIDENTALLY ORPHANING THE OMNIBRIDGE WITH INCORRECT CONFIGURATION***

 

Note: If this OmniBridge was ordered with more than one WAN link, MDS recommends that you configure static links one at a time, leaving one in DHCP mode as a backup.  Once the static IP is confirmed functional, you can then proceed configuring a second static IP on the other WAN link (if necessary).

 

To configure your OmniBridge for use on WAN connection with a static IP:

1. Connect your OmniBridge to an upstream network with a DHCP server running (as described above)

2. Once it is showing online, go to the OmniWAN tab on your subscription and click "EDIT" on the corresponding WAN port you want to configure to static IP

Screen_Shot_2017-07-10_at_7.40.44_PM.png

3. VERY CAREFULLY, enter the static IP information you confirmed with the ISP and hit save.

Screen_Shot_2017-07-10_at_7.55.25_PM.png

4. Connect the corresponding OmniBridge WAN port you configured to WAN port of the respective ISP

 - Verify WAN link shows online on the portal

Screen_Shot_2017-07-10_at_11.06.35_PM.png

 

*Upstream bandwidth shared with other routers can impact the OmniBridge's ability to offer the best, if this configuration is required, consult with MDS Support regarding the topology as some additional review may be necessary.

Have more questions? Submit a request
Powered by Zendesk